![background image](http://html1.mh-extra.com/html/omron/sysmac-cj1w-scu21-v1/sysmac-cj1w-scu21-v1_operation-manual_743586423.webp)
394
C-mode (Host Link) Command Master
Appendix C
Command Frame Contents
Response Frame Contents
For details on C-mode command codes for sending to CS/CJ-series CPU Units, refer to the
CS/CJ Series
Communications Commands Reference Manual
(W342). For details on C-mode command codes for sending
to C-series CPU Units, refer to each of the C-series PLC operation manuals.
C-mode Command Code Master Protocol Sequences
The C-mode (Host Link) Command Code Master Protocol provides the following 22 communications
sequences.
Structure of the Protocol
The following table shows the structure of the C-mode (Host Link) Command Code Master Protocol.
Item
Contents
@
Must be attached at the beginning of the command.
Host Link unit num-
ber
Set the unit number in BCD from 0 to 31 for each Host Link.
Command code
The command code is specified in two characters
Text
Set parameters corresponding to command code.
FCS
Calculate 2-character FCS (frame check sequence) at host
computer.
Terminator
Set “*” and CR (0DH) as two characters to indicate the end of
the command.
Item
Contents
@
Must be attached at the beginning of the response.
Host Link unit num-
ber
Set the unit number in BCD from 0 to 31 for each Host Link.
Command code
The command code that was received is returned.
End code
The results (error status, etc.) of command execution is
returned.
Text
Returned only if there is read data.
FCS
The 2-character FCS (frame check sequence) is returned.
Terminator
Two characters indicating the end of the command, “*” and CR
(0D hex), are returned.
Sequence
No.
Communications
sequence name
Function
Ladder interface
Send word
allocation
Receive
word
allocation
700 (02BC)
Send/receive C-
mode command
(with ASCII conver-
sion)
Converts the text data for the specified C-mode com-
mand into ASCII and sends to the specified Host Link
Unit. The response is converted into hexadecimal and
stored starting from the specified word.
Yes
Yes
701 (02BD)
Send/receive C-
mode command
(without conversion)
Sends the text data for the specified C-mode command
to the specified Host Link Unit without converting into
ASCII. The response is stored starting from the specified
word without converting into hexadecimal.
Yes
Yes
702 (02BE)
CIO AREA READ
Reads the contents of the specified number of CIO Area
words beginning with the designated word from the spec-
ified Host Link Unit and stores starting from the specified
storage word.
Yes
Yes
Summary of Contents for SYSMAC CJ1W-SCU21-V1
