![background image](http://html1.mh-extra.com/html/omron/sysmac-cj1w-scu21-v1/sysmac-cj1w-scu21-v1_operation-manual_743586160.webp)
131
Auxiliary Area and CIO Area Allocations
Section 4-3
Note
The settings in the Setup Area are reflected here. The default settings will be
used and will be stored here if a setup error occurs.
Error Log EEPROM Error
This bit will be set to 1 if an error occurs in reading or writing the error log
stored in EEPROM on the assumption that the EEPROM has reached its use-
ful life. If a Serial Communications Unit is being used, the ERC indicator will
also light. If a Serial Communications Board is being used, A42411 will turn
ON and the ERR/ALM indicator on the CPU Unit will flash, indicating a non-
fatal error.
Protocol Data Error
This bit will be turned ON if a checksum error is detected in the protocol data
at startup. The checksum is checked for all serial communications modes. If a
Serial Communications Unit is being used, the ERC indicator will also flash. If
a Serial Communications Board is being used, A42409 will turn ON, the ERR/
ALM indicator on the CPU Unit will flash, and the RDY indicator will flash at 1-
second intervals, indicating a non-fatal error.
CIO
1905
CIO
1915
n + 5
n + 15
12 to 15
Port
setting
status
Setup
settings
Serial communications mode
08 to 11
Baud rate (See note.)
05 to 07
Reserved
04
Start bits: Always 0
03
Data length: 7 or 8 bits (See note.)
02
Stop bits: 1 or 2 bits (See note.)
01
Parity: Yes/No (Note)
00
Parity: Even/Odd (Note)
CIO
1906
CIO
1916
n + 6
n + 16
15
Hard-
ware
settings
14
13
0: Terminating resistance OFF
1: Terminating resistance ON
02 to 12
Reserved
01
1: Setup error; 0: Setup normal
00
1: Port operating; 0: Port stopped
CIO
1907
CIO
1917
n + 7
n + 17
11 to 15
Commu-
nica-
tions
status
Reserved
10
Undetermined
09
Reserved
08
Always 0
07
Trans-
mission
control
signal
status
ER signal
06
DTR signal
05
Reserved
04
CTS signal
03
RTS signal
00 to 02
Reserved
CIO
1908
CIO
1918
n + 8
n + 18
15
Trans-
mission
error sta-
tus
1: Transmission error; 0: No transmission error
05 to 14
Not used.
04
1: Overrun error; 0: Normal
03
1: Framing error; 0: Normal
02
1: Parity error; 0: Normal
00, 01
Reserved
Words
Bit
Contents
Boards
(CS Series only)
Units
(CS/CJ Series)
Port 1
Port 2
Port 1
Port 2
0 No 0 RS-232C 1 RS-422A/485 1 Reserved
0
1
0 1
Summary of Contents for SYSMAC CJ1W-SCU21-V1
