![background image](http://html1.mh-extra.com/html/omron/sysmac-cj1w-scu21-v1/sysmac-cj1w-scu21-v1_operation-manual_743586078.webp)
49
Basic Operating Procedure
Section 1-9
NT Link Mode
The following table shows the default (standard) settings for NT link when the
maximum PT unit number is 5.
m = 100
×
unit number
Serial Gateway
Using Serial Gateway Alone
1.
Make the settings in the Setup Area.
m = 100
×
unit number
2.
Set the local network table in the routing tables as required (using CX-Net).
Using Serial Gateway During Protocol Macro Execution
1.
Make the settings in the Setup Area.
m = 100
×
unit number
D32008
D32018
m + 8
m + 18
15
0
Half-duplex
D32009
D32019
m + 9
m + 19
15 to 00
00C8 hex
Maximum number of bytes in protocol
macro send/receive data: 200 bytes
Board
(CS Series only)
Unit
(CS/CJ Series)
Bit
Setting
Meaning
Port 1
Port 2
Port 1
Port 2
Board
(CS Series only)
Unit
(CS/CJ Series)
Bit
Setting
Meaning
Port 1
Port 2
Port 1
Port 2
D32000
D32010
m
m + 10
11 to 08
2
1:N NT Link
D32001
D32011
m + 1
m + 11
03 to 00
0
The baud rate is set to the standard NT link
setting when the default settings are used.
D32006
D32016
m + 6
m + 16
02 to 00
5
1:N NT Link maximum unit number
(example)
Board
(CS Series only)
Unit
(CS/CJ Series)
Bit
Setting
Meaning
Port 1
Port 2
Port 1
Port 2
D32000
D32010
m
m+10
15
0
Start bits: 1 bit
Data length: 7 bits
Parity: Even
Stop bits: 2
Baud rate: 9,600 bps
11 to 08
9 hex
Serial communications mode: Serial Gate-
way
D32002
D32012
m+2
m+12
15
0
Send delay: 0 ms
D32003
D32013
m+3
m+13
15
0
CTS control: No
D32007
D32017
m+7
m+17
15 to 08
00 hex
Response timeout monitoring time: 5 s
Board
(CS Series only)
Unit
(CS/CJ Series)
Bit
Setting
Meaning
Port 1
Port 2
Port 1
Port 2
D32000
D32010
m
m+10
11 to 08
6 hex
Serial communications mode: Protocol
macro
D32002
D32012
m+2
m+12
15
0
Send delay: 0 ms
D32003
D32013
m+3
m+13
15
0
CTS control: No
D32007
D32017
m+7
m+17
15 to 08
00 hex
Response timeout monitoring time: 5 s
07 to 00
00 hex
Serial Gateway send start timeout monitor-
ing time: 5 s
Summary of Contents for SYSMAC CJ1W-SCU21-V1
