![background image](http://html1.mh-extra.com/html/omron/sysmac-cj1w-scu21-v1/sysmac-cj1w-scu21-v1_operation-manual_743586109.webp)
80
I/O Memory Allocations
Section 2-3
Software Switches
Software Switches are used to output control signals from the CPU Unit to the
Serial Communications Board or Unit. The software switches are used for
loopback tests and to abort, release wait status, and control other functions
for protocol macros. For details on the software switch functions, refer to
Sec-
tion 5 Using Protocol Macros
and
Section 10 Loopback Test
.
n = CIO 1500 + 25
×
unit number
Note
The One-shot Trace Switch and Continuous Trace Switch are used for the
Serial Communications Board/Unit only when executing traces from the CX-
Protocol in protocol macro mode. Do not manipulate these switches from a
ladder diagram.
Status Area
The Status Area is used for status information input from Serial Communica-
tions Board or Unit to the CPU Unit. The Status Area is where the Serial Com-
munications Board or Unit sets communications status, the transmission
control signal status, the transmission error status, and the protocol status.
Words
Bit
Function
Board
(CS
only)
Unit
(CS/
CJ)
CIO
1900
n
15
Port 2
Reserved
14
Loopback Test Switch (loopback tests)
1: Start, 0: Stop
13
Reserved
12
Serial Gateway Prohibited Switch (protocol mac-
ros)
1: Prohibited, 0: Not prohibited
11
Abort Switch (protocol macros)
1: Abort, 0: Aborted
10
One-shot Trace Switch (protocol macros, see
note)
1: Start, 0: Stop
09
Continuous Trace Switch
(protocol macros, see note)
1: Start, 0: Stop
08
Wait Release Switch (protocol macros)
1: Release wait, 0: Wait released
07
Port 1
Reserved
06
Loopback Test Switch (loopback tests)
1: Start, 0: Stop
05
Reserved
04
Serial Gateway Prohibited Switch (protocol mac-
ros)
1: Prohibited, 0: Not prohibited
03
Abort Switch (protocol macros)
1: Abort, 0: Aborted
02
One-shot Trace Switch (protocol macros, see
note)
1: Start, 0: Stop
01
Continuous Trace Switch
(protocol macros, see note)
1: Start, 0: Stop
00
Wait Release Switch (protocol macros)
1: Release wait, 0: Wait released
Summary of Contents for SYSMAC CJ1W-SCU21-V1
