292
Communications Timing
Section 9-4
tion is completed. When creating the ladder diagram, use these flags as input
conditions when executing these instructions.
Communications Port
Error Flags
A Communications Port Error Flag will turn ON in the following cases.
• When an error is generated during execution of SEND(090), RECV(098),
or CMND(490).
• When an error response or retry error has been generated for the port.
These Flags will turn OFF when the corresponding Communications Port
Enabled Flag is turned OFF at the start of operation or at the start of execut-
ing the SEND(090), RECV(098), or CMND(490).
Communications Port
Completion Codes
The Communications Port Completion Code words will contain the FINS end
code after SEND(090), RECV(098), or CMND(490) has been executed.
If the Communications Port Enabled Flag turns OFF when operation is started
or SEND(090), RECV(098), or CMND(490) are executed, the contents of
these words will be cleared.
Word
Bit
Content
A202
08 to 15
Reserved
07
Communications Port Enabled Flag, Port No. 7
06
Communications Port Enabled Flag, Port No. 6
05
Communications Port Enabled Flag, Port No. 5
04
Communications Port Enabled Flag, Port No. 4
03
Communications Port Enabled Flag, Port No. 3
02
Communications Port Enabled Flag, Port No. 2
01
Communications Port Enabled Flag, Port No. 1
00
Communications Port Enabled Flag, Port No. 0
Word
Bit
Content
A219
08 to 15
Reserved
07
Communications Port Error Flag, Port No. 7
06
Communications Port Error Flag, Port No. 6
05
Communications Port Error Flag, Port No. 5
04
Communications Port Error Flag, Port No. 4
03
Communications Port Error Flag, Port No. 3
02
Communications Port Error Flag, Port No. 2
01
Communications Port Error Flag, Port No. 1
00
Communications Port Error Flag, Port No. 0
Word
Content
A203
Communications Port Completion Code, Port No. 0
A204
Communications Port Completion Code, Port No. 1
A205
Communications Port Completion Code, Port No. 2
A206
Communications Port Completion Code, Port No. 3
A207
Communications Port Completion Code, Port No. 4
A208
Communications Port Completion Code, Port No. 5
A209
Communications Port Completion Code, Port No. 6
A210
Communications Port Completion Code, Port No. 7
A211 to A218
Reserved
Summary of Contents for SYSMAC CJ1W-SCU21-V1
