51
Basic Operating Procedure
Section 1-9
Modbus-RTU Slave Mode
The following example is for the default (standard) communications condi-
tions, with the Modbus slave address set to 1 and the default allocation areas
for Coils, Input Registers, and Holding Registers.
m = 100
×
unit number
Validate the New Settings
Make the new settings in the Setup Area valid by performing one of the follow-
ing.
• Turn the power OFF and then ON again. The Setup Area allocated in the
DM Area will be read when the power is turned ON.
• Restart the Board by turning ON the Inner Board Restart Bit (A60800) or
restart the Unit turning ON one of the CPU Bus Unit Restart Bits (A50100
to A50115, where the bit number corresponds to the unit number). (See
following table.)
• Restart the port on the Serial Communications Board by turning ON one
of the Communications Board Port Settings Change Bits (A63601 for port
1 and A63602 for port 2) or restart the port on the Serial Communications
Unit by tuning ON one of the Communications Unit Port Settings Change
Bits (A620 to A635: The word will be A620 + unit number and the bit will
be bit 01 for port 1 and bit 02 for port 2).
Board
(CS Series only)
Unit
(CS/CJ Series)
Bit
Setting
Meaning
Port 1
Port 2
Port 1
Port 2
D32000
D32010
m
m+10
15
0
Defaults
Parity: Even
Stop bits: 1 bit
Baud rate: 19,200 bps
(Start bits: 1 bit, Data length: 8 bits)
11 to 08
A hex
Modbus-RTU slave
D32001
D32011
m+1
m+11
03 to 00
0 hex
Disabled for default communications condi-
tions (baud rate: 19,200 bps)
D32006
D32016
m+6
m+16
15 to 08
1 hex
Modbus slave address: 1
D32020
D32030
m+20
m+30
07 to 00
0 hex
Coils allocation area: CIO Area
D32021
D32031
m+21
m+31
15 to 08
0 hex
Input Registers allocation area: CIO Area
07 to 00
0 hex
Holding Registers allocation area: DM Area
Summary of Contents for SYSMAC CJ1W-SCU21-V1
