NEC PD703114 User Manual Download

Page: 608 / 692

CHAPTER 15 FLASH MEMORY (

PD70F3114)

608

User’s Manual U15195EJ5V0UD

15.5 Pin Connection

When performing on-board writing, install a connector on the target system to connect to the dedicated flash

programmer. Also, install a function on-board to switch from the normal operation mode (single-chip mode or

ROMless mode) to the flash memory programming mode.

In the flash memory programming mode, all the pins not used for flash memory programming become the same

status as they were immediately after reset in single-chip mode. Therefore, all the ports become output high-

impedance status, so that pin connection is required when the external device does not acknowledge the output high-

impedance status.

15.5.1 MODE1/V

pin

In the normal operation mode, 0 V is input to the MODE1/V

pin. In the flash memory programming mode, 7.8 V

writing voltage is supplied to the MODE1/V

pin. The following shows an example of the connection of the

MODE1/V

pin.

Figure 15-5. Connection Example of MODE1/V

Pin

V850E/IA2

MODE1/V

Pull-down resistor (R

VPP

= 5 to 50 k

Ω

)

Dedicated flash programmer connection pin

15.5.2 Serial interface pin

The following shows the pins used by each serial interface.

Table 15-3. Pins Used by Each Serial Interface

Serial Interface

Pins Used

CSI0

SO0, SI0, SCK0

CSI0 + HS

SO0, SI0, SCK0, PDH0

UART0 TXD0,

RXD0

When connecting a dedicated flash programmer to a serial interface pin that is connected to other devices on-

board, care should be taken to avoid the conflict of signals and the malfunction of other devices, etc.

(1) Conflict of signals

When connecting a dedicated flash programmer (output) to a serial interface pin (input) which is connected to

another device (output), a conflict of signals occurs. To avoid the conflict of signals, isolate the connection to

the other device or set the other device to the output high-impedance status.

Summary of Contents for PD703114





















































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for PD703114

Reviews:

Related manuals for PD703114

Brands by name

Popular brands

NEC PD703114, User Manual

Search results

Summary of Contents for PD703114

Reviews:

Related manuals for PD703114

Brands by name

Popular brands