Lenovo System x3550 M5 Installation And Service Manual Download Page 414

Page: 414 / 1144

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

Fan 4B Tach :

•

80010204-1d05ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 5A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d05ffff or 0x800102041d05ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

Fan 5B Tach :

400

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands