Lenovo System x3550 M5 Installation And Service Manual Download Page 737

Page: 737 / 1144

•

81010902-0701ffff : Numeric sensor [NumericSensorElementName] going high (upper critical) has

deasserted. (SysBrd 12V)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has deasserted.

May also be shown as 810109020701ffff or 0x810109020701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

No action; information only. SysBrd 3.3V : SysBrd 5V :

•

81010b01-0f01ffff : Numeric sensor [NumericSensorElementName] going high (upper

non-recoverable) has deasserted. (REAR BP Temp A)

This message is for the use case when an implementation has detected an Upper Non-recoverable sensor
going high has deasserted.

May also be shown as 81010b010f01ffff or 0x81010b010f01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0499

User Response

No action; information only.

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

723

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands