Lenovo System x3550 M5 Installation And Service Manual Download Page 1085

Page: 1085 / 1144

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-801-000 : MemStr Test Aborted

Internal program error.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Turn off and restart the system.

2. Make sure that the DSA Diagnostic code is at the latest level.

3. Run the test again.

4. If the system has stopped responding, turn off and restart the system.

5. Check the system firmware level and upgrade if necessary.

6. Run the memory diagnostic to identify the specific failing DIMM.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-802-000 : MemStr Test Aborted

Memory size is insufficient to run the test. At least 1 GB is required.

Recoverable

Severity

Warning

Appendix C. DSA diagnostic test results

1071

«
...
1083
1084
1085
1086
1087
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands