Lenovo System x3550 M5 Installation And Service Manual Download Page 34

Page: 34 / 1144

Scroll down button

Select button

Scroll up button

LCD system information display panel

Figure 17. LCD operating panel assembly

•

Scroll up button:

Press this button to scroll up or scroll to the left in the main menu to locate and select

the system information that you want displayed.

•

Select button:

Press this button to make your selection from the menu options.

•

Scroll down button:

Press this button to scroll down or scroll to the right in the main menu to location

and select the system information that you want displayed.

The following is an illustration of the LCD operating panel assembly menu options flow.

Reset

IMM

default

settings

Re que s t

IMM

Hard Reset

Re que s t

IMM

Soft Reset

Cle a r C MOS

Reset

IMM

default

settings

Figure 18. LCD operating panel assembly menu options flow

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands