Lenovo System x3550 M5 Installation And Service Manual Download Page 816

Page: 816 / 1144

This message is for the use case when an implementation has detected an Array Failure is no longer
Predicted.

May also be shown as 816f020d0400ffff or 0x816f020d0400ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0169

User Response

No action; information only.

•

816f020d-0401ffff : Failure no longer Predicted on drive [StorageVolumeElementName] for array

[ComputerSystemElementName]. (Drive 1)

This message is for the use case when an implementation has detected an Array Failure is no longer
Predicted.

May also be shown as 816f020d0401ffff or 0x816f020d0401ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0169

User Response

No action; information only.

802

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands