Lenovo System x3550 M5 Installation And Service Manual Download Page 1086

Page: 1086 / 1144

Serviceable

Yes

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-803-000 : MemStr Test Aborted

User pressed Ctrl-C.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-901-000 : MemStr Test Failed

Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Execute the standard DSA memory diagnostics to validate all memory.

2. Make sure that the DSA Diagnostic code is at the latest level.

3. Turn off the system and disconnect it from power.

4. Reseat the memory cards and DIMMs.

5. Reconnect the system to power and turn the system on.

1072

Lenovo System x3550 M5 Installation and Service Guide

«
...
1084
1085
1086
1087
1088
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands