Lenovo System x3550 M5 Installation And Service Manual Download Page 880

Page: 880 / 1144

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0817

User Response

No action; information only.

•

816f0607-2584ffff : An SM BIOS Uncorrectable CPU complex error for [ProcessorElementName]

has deasserted. (All CPUs)

This message is for the use case when an SM BIOS Uncorrectable CPU complex error has deasserted.

May also be shown as 816f06072584ffff or 0x816f06072584ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0817

User Response

No action; information only. One of the CPUs :

•

816f0608-1301ffff : [PowerSupplyElementName] Configuration is OK. (PS Configuration)

This message is for the use case when an implementation when a Power Supply configuration is OK.

May also be shown as 816f06081301ffff or 0x816f06081301ffff

866

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands