manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

• Locate the documentation that comes with the drive and follow those instructions in addition to the

instructions in this chapter.

• Make sure that you have all the cables and other equipment that are specified in the documentation that

comes with the drive.

• The server supports one ultra-slim SATA DVD drive.

To install a DVD drive, complete the following steps:

Note:

The DVD drive is available on some models.

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Note:

When you disconnect the power source from the server, you lose the ability to view the LEDs

because the LEDs are not lit when the power source is removed. Before you disconnect the
power source, make a note of which LEDs are lit, including the LEDs that are lit on the operation
information panel and LEDs inside the server on the system board.

Step 3.

Remove the cover (see “Removing the cover” on page 119).

Step 4.

Remove the DVD drive filler panel if it is installed. Locate the blue release tab on the rear of the DVD
drive filler panel; then, while you press the tab, push the DVD drive filler panel out of the drive bay.

DVD drive filler panel

Release tab

Figure 74. DVD drive filler panel removal for 2.5-inch hard disk drive server models

150

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Canon ColorPASS-Z5000 Getting Started preview
ColorPASS-Z5000
Brand: Canon Pages: 130
F5 ARX-2500 Installation Manual preview
ARX-2500
Brand: F5 Pages: 2
F5 WANJet 400 Appliance Upgrade Instructions preview
WANJet 400 Appliance
Brand: F5 Pages: 11
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Brand: Supero Pages: 112
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Brand: American Megatrends Pages: 2
Supero SuperServer 5013C-MT User Manual preview
SuperServer 5013C-MT
Brand: Supero Pages: 98
Icy Box IB-NAS902 User Manual preview
IB-NAS902
Brand: Icy Box Pages: 17
H3C UniServer R4300 G6 User Manual preview
UniServer R4300 G6
Brand: H3C Pages: 542
Waves WSG SoundGrid Server One User Manual preview
WSG SoundGrid Server One
Brand: Waves Pages: 4
HazSim Pro 2.0 User Manual preview
Pro 2.0
Brand: HazSim Pages: 27
Chip PC Xtreme PC NG6050 Specifications preview
Xtreme PC NG6050
Brand: Chip PC Pages: 4
Red Hat NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT Installation Manual preview
NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT
Brand: Red Hat Pages: 74
Meinberg IMS LANTIME M4000 Manual preview
IMS LANTIME M4000
Brand: Meinberg Pages: 138
Meinberg SyncFire 1200 Manual preview
SyncFire 1200
Brand: Meinberg Pages: 55
TAG SV-4102-X214 Operation Manual preview
SV-4102-X214
Brand: TAG Pages: 50
3onedata NP5100 Series Quick Installation Manual preview
NP5100 Series
Brand: 3onedata Pages: 4
Uniwide UniServer 1522LV User Manual preview
UniServer 1522LV
Brand: Uniwide Pages: 68
thomann T.racks DSP 26 User Manual preview
T.racks DSP 26
Brand: thomann Pages: 60

Brands by name

Popular brands

Load more brands