Lenovo System x3550 M5 Installation And Service Manual Download Page 1004

Page: 1004 / 1144

Test results for the DSA Mellanox adapter test

The following messages can result when you run the DSA Mellanox adapter test.

•

408-000-000 : MLNX:MLNX_DiagnosticTestEthernetPort Test Passed

Port Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-001-000 : MLNX:MLNX_DiagnosticTestIBPort Test Passed

Port Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-800-000 : MLNX:MLNX_DiagnosticTestEthernetPort Test Aborted

Port Test was canceled.

Recoverable

Severity

Warning

Serviceable

990

Lenovo System x3550 M5 Installation and Service Guide

«
...
1002
1003
1004
1005
1006
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands