Lenovo System x3550 M5 Installation And Service Manual Download Page 283 | Manualshive

Page: 283 / 1144

background image

• The microprocessor installation tool has the microprocessor installed on the tool, and may have a

protective cover over the microprocessor. Do not use the tool, or remove the cover until you are
instructed to do so.

Note:

Be sure to use the installation tool that comes with your microprocessor installation tool assembly.

The tool has two settings for installing two different sizes of microprocessors. The settings that are marked
on the tool are “L” for smaller low core microprocessors, and “H” for larger high core microprocessors.

Microprocessor Installation Tool

Microprocessor

Installation tool

Figure 199. Microprocessor installation tool

To replace a microprocessor and heat sink, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Attention:

When you handle static-sensitive devices, take precautions to avoid damage from static

electricity. For details about handling these devices, see “Handling static-sensitive devices” on
page 118.

Step 3.

Remove the cover (see “Removing the cover” on page 119).

Step 4.

Remove the air baffle (see “Removing the air baffle” on page 122).

Removing and replacing components

269

«
...
281
282
283
284
285
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Brand: Obvius Pages: 29

APSolute Vision

Brand: Radware Pages: 81

Brand: Xyplex Pages: 58

SUPERSERVER 1018D-73MTF

Brand: Supero Pages: 124

EMC VxFlex Appliance R840

Brand: Dell Pages: 44

EqualLogic PS4000

Brand: Dell Pages: 73

EMC PowerProtect DD6400 System

Brand: Dell Pages: 46

EqualLogic PS5500

Brand: Dell Pages: 8

Brand: Dell Pages: 22

External OEMR R210II

Brand: Dell Pages: 126

External OEMR R210

Brand: Dell Pages: 144

External OEMR XL R210

Brand: Dell Pages: 72

POWER EDGE SC1430

Brand: Dell Pages: 160

EMC PowerEdge XE8545

Brand: Dell Pages: 33

EMC PowerEdge T640 D24XR

Brand: Dell Pages: 166

Brand: Dell Pages: 68

Brand: Dell Pages: 66

Brand: Dell Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands