Lenovo System x3550 M5 Installation And Service Manual Download Page 740

Page: 740 / 1144

•

81010b01-1301ffff : Numeric sensor [NumericSensorElementName] going high (upper

non-recoverable) has deasserted. (PSU 1 Amb Temp)

This message is for the use case when an implementation has detected an Upper Non-recoverable sensor
going high has deasserted.

May also be shown as 81010b011301ffff or 0x81010b011301ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0499

User Response

No action; information only.

•

81010b01-1302ffff : Numeric sensor [NumericSensorElementName] going high (upper

non-recoverable) has deasserted. (PSU 2 Amb Temp)

This message is for the use case when an implementation has detected an Upper Non-recoverable sensor
going high has deasserted.

May also be shown as 81010b011302ffff or 0x81010b011302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0499

User Response

No action; information only.

726

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands