manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

•

806f010d-040cffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 12)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d040cffff or 0x806f010d040cffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-040dffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 13)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d040dffff or 0x806f010d040dffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

523

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Gateway ALR 7300 Maintaining And Troubleshooting preview
ALR 7300
Brand: Gateway Pages: 138
Edimax PS-1208MFg User Manual preview
PS-1208MFg
Brand: Edimax Pages: 93
Novell NETWARE 6 Manual preview
NETWARE 6
Brand: Novell Pages: 152
IBM IntelliStation R Pro Hardware Maintenance Manual preview
IntelliStation R Pro
Brand: IBM Pages: 194
Fujitsu Siemens Computers PRIMERGY B120 Operating Manual preview
PRIMERGY B120
Brand: Fujitsu Siemens Computers Pages: 68
Novell ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER User Manual preview
ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER
Brand: Novell Pages: 390
Supermicro SUPERSERVER 5019S-M User Manual preview
SUPERSERVER 5019S-M
Brand: Supermicro Pages: 65
Intel SRPM8 Quick Start Manual preview
SRPM8
Brand: Intel Pages: 32
Infortrend EonStor GS 3000 Series Hardware Manual preview
EonStor GS 3000 Series
Brand: Infortrend Pages: 134
PRG MBOX 2016 Hardware Manual preview
MBOX 2016
Brand: PRG Pages: 50
Xblue Networks X16plus Quick Start Manual preview
X16plus
Brand: Xblue Networks Pages: 2
Intergraph InterServe 90 System Setup preview
InterServe 90
Brand: Intergraph Pages: 102
D-Link DP-100 Hardware User'S Manual preview
DP-100
Brand: D-Link Pages: 32
D-Link DP-101 Hardware Manual preview
DP-101
Brand: D-Link Pages: 22
D-Link DP-313 - Air 802.11b Wireless Print Server User Manual preview
DP-313 - Air 802.11b Wireless Print Server
Brand: D-Link Pages: 28
D-Link DP 301U Quick Installation Manual preview
DP 301U
Brand: D-Link Pages: 64
D-Link D DP-301P+ DP-301P+ Datasheet preview
D DP-301P+ DP-301P+
Brand: D-Link Pages: 2
D-Link DP-802 User Manual preview
DP-802
Brand: D-Link Pages: 100

Brands by name

Popular brands

Load more brands