Lenovo System x3550 M5 Installation And Service Manual Download Page 245

Page: 245 / 1144

Step 5.

Locate the coin-cell battery on the system board.

Coin-cell battery

Figure 149. Location of the coin-cell battery on system board

If there is a rubber cover on the battery holder, use your fingers to lift the battery cover from
the battery connector.

Use one finger to tilt the battery horizontally out of its socket, pushing it away from the socket.

Attention:

Neither tilt nor push the battery by using excessive force.

Figure 150. Coin-cell battery removal

Use your thumb and index finger to lift the battery from the socket.

Attention:

Do not lift the battery by using excessive force. Failing to remove the battery

properly may damage the socket on the system board. Any damage to the socket may require
replacing the system board.

Step 6.

Dispose of the battery as required by local ordinances or regulations.

Chapter 5

Removing and replacing components

231

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands