Lenovo System x3550 M5 Installation And Service Manual Download Page 721

Page: 721 / 1144

•

81010204-1d07ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 7A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d07ffff or 0x810102041d07ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 7B Tach :

•

81010204-1d08ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 8A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d08ffff or 0x810102041d08ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 8B Tach :

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

707

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands