Lenovo System x3550 M5 Installation And Service Manual Download Page 347

Page: 347 / 1144

User Response

Information only; no action is required.

•

40000052-00000000 : Server [arg1] scheduled for [arg2] at [arg3] by user [arg4].

A user configured a Server Power action at a specific time

May also be shown as 4000005200000000 or 0x4000005200000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0082

User Response

Information only; no action is required.

•

40000053-00000000 : Server [arg1] scheduled for every [arg2] at [arg3] by user [arg4].

A user configured a recurring Server Power Action

May also be shown as 4000005300000000 or 0x4000005300000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0083

User Response

Information only; no action is required.

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

333

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands