manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 7.

Route the backplane signal cables. The following illustrations apply to SAS/SATA adapters that
are inserted into the dedicated connector on the system board.

SAS/SATA power
connector

SAS/SATA
configuration
connector

SAS/SATA configuration
and power cable

SAS/SATA signal
cable

Figure 112. ServeRAID adapter cable routing for four 3.5-inch hot-swap hard disk drive configuration

188

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

IBM 847620U - Netfinity 3000 - 20U Hardware Maintenance Manual preview
847620U - Netfinity 3000 - 20U
Brand: IBM Pages: 270
TYANO GX38-B5550 Service Engineer'S Manual preview
GX38-B5550
Brand: TYANO Pages: 68
Buffalo TeraStation WSS WS5020N6 User Manual preview
TeraStation WSS WS5020N6
Brand: Buffalo Pages: 115
ORiNG IDS-5042 Series User Manual preview
IDS-5042 Series
Brand: ORiNG Pages: 67
MAXDATA PLATINUM 1500 IR M5 User Manual preview
PLATINUM 1500 IR M5
Brand: MAXDATA Pages: 44
Auspex Systems NS 7000 150 Hardware Release Note preview
NS 7000 150
Brand: Auspex Systems Pages: 52
Siemens APOGEE Ethernet Microserver 2100 Installation Instructions preview
APOGEE Ethernet Microserver 2100
Brand: Siemens Pages: 2
Siemens OCI670 Series Installation Instructions Manual preview
OCI670 Series
Brand: Siemens Pages: 38
Siemens 3964R User Manual preview
3964R
Brand: Siemens Pages: 40
Siemens RUGGEDCOM RS401 Installation Manual preview
RUGGEDCOM RS401
Brand: Siemens Pages: 50
Siemens PRIMERGY 560 Operating Manual preview
PRIMERGY 560
Brand: Siemens Pages: 101
Siemens OZW672 Series Commissioning Instructions preview
OZW672 Series
Brand: Siemens Pages: 116
Siemens OZW672.01 Commissioning Instructions preview
OZW672.01
Brand: Siemens Pages: 143
Siemens HiPath Xpressions User Manual preview
HiPath Xpressions
Brand: Siemens Pages: 278
Siemens Advanced Server UNIX V4.0 Overviews & Installation Instructions preview
Advanced Server UNIX V4.0
Brand: Siemens Pages: 365
Chip PC JackPC EFI-6700 Specifications preview
JackPC EFI-6700
Brand: Chip PC Pages: 4
IBM 206m - eServer xSeries - 8485 Installation Manual preview
206m - eServer xSeries - 8485
Brand: IBM Pages: 110
IBM 1911 Service Manual preview
1911
Brand: IBM Pages: 268

Brands by name

Popular brands

Load more brands