Lenovo System x3550 M5 Installation And Service Manual Download Page 902

Page: 902 / 1144

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0179

User Response

No action; information only.

•

816f070d-0402ffff : Rebuild completed for Array in system [ComputerSystemElementName].

(Drive 2)

This message is for the use case when an implementation has detected that an Array Rebuild has
Completed.

May also be shown as 816f070d0402ffff or 0x816f070d0402ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0179

User Response

No action; information only.

•

816f070d-0403ffff : Rebuild completed for Array in system [ComputerSystemElementName].

(Drive 3)

This message is for the use case when an implementation has detected that an Array Rebuild has
Completed.

May also be shown as 816f070d0403ffff or 0x816f070d0403ffff

888

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands