Lenovo System x3550 M5 Installation And Service Manual Download Page 216 | Manualshive

Page: 216 / 1144

background image

• These power supplies are designed for parallel operation. In the event of a power-supply failure, the

redundant power supply continues to power the system. The server supports a maximum of two
power supplies.

CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.

1

2

CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with
one of these parts, contact a service technician.

To install a hot-swap ac power supply, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Touch the static-protective package that contains the hot-swap power supply to any unpainted
metal surface on the server; then, remove the power supply from the package and place it on
a static-protective surface.

202

Lenovo System x3550 M5 Installation and Service Guide

«
...
214
215
216
217
218
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

SuperServer E100-8Q

Brand: Supermicro Pages: 48

Brand: Cabletron Systems Pages: 93

Brand: IESC Pages: 109

UniServer E3200 G3

Brand: H3C Pages: 401

Brand: Cable-Tronix Pages: 33

Brand: Ericsson Pages: 159

Brand: Moxa Technologies Pages: 100

Rackmount 5000 Series

Brand: Johnson Controls Pages: 42

@server x Series

Brand: IBM Pages: 8

Brand: QNAP Pages: 58

Brand: IEI Technology Pages: 130

Brand: BITMAIN Pages: 15

Brand: EVS Pages: 198

Brand: Kramer Pages: 28

Brand: Gigabyte Pages: 108

NETWORK SATELLITE 5.0.0 -

Brand: Red Hat Pages: 84

Brand: Vision Hi-Tech Pages: 2

21000 Appliances G-70

Brand: Check Point Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands