Lenovo System x3550 M5 Installation And Service Manual Download Page 147

Page: 147 / 1144

Step 3.

Slide the tray until it snaps into position in the chassis.

Figure 50. Installing the RAID adapter battery or flash power module holder

Step 4.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 5.

Slide the server into the rack.

Step 6.

Reconnect the power cords and all external cables, and turn on the server and peripheral devices.

Removing the EIA bracket

Use this information to remove the EIA bracket.

To remove the EIA bracket, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

If necessary, turn off the server and peripheral devices and disconnect the power cords and all
external cables.

Step 3.

If the server has been installed in a rack, slide the server out from the rack enclosure.

Chapter 5

Removing and replacing components

133

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands