Lenovo System x3550 M5 Installation And Service Manual Download Page 229

Page: 229 / 1144

Steps for installing a ten 2.5-inch hot-swap hard disk drive backplane with two NVMe drive
connectors

Align the backplane with the slots on the chassis.

Carefully lower the hard disk drive backplane until it is fully seated in the chassis.

Ten 2.5-inch hard disk drive backplane
(with two NVMe connectors)

Figure 134. Installation of a 10 x 2.5-inch hot-swap hard disk drive backplane with two NVMe connectors

Install the NVMe adapter to the PCI Express slot 2 (low-profile). See “Replacing an adapter”
on page 178.

Note:

You can view the NVMe adapter information in the Setup Utility program only when your

server has the following hardware installed:

• PCIe riser 2 assembly (FRU number: 00KF627)

• Two microprocessors

Chapter 5

Removing and replacing components

215

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands