Lenovo System x3550 M5 Installation And Service Manual Download Page 192 | Manualshive

Page: 192 / 1144

background image

00

Adapter

Adapter

Expansion
filler

Expansion
filler

Figure 103. Adapter removal from a PCI riser-card assembly that has two low-profile slots (for PCI riser-card
assembly connector 2 on system board)

00

00

Adapter

Adapter

Expansion
filler

Expansion
filler

Figure 104. Adapter removal from a PCI riser-card assembly that has one low-profile slot and one full-height
half-length slot (for PCI riser-card assembly connector 2 on system board)

If you are instructed to return the adapter, follow all packaging instructions, and use any packaging materials
for shipping that are supplied to you.

Replacing an adapter

The following notes describe the types of adapters that the server supports and other information that
you must consider when you install an adapter.

• Locate the documentation that comes with the adapter and follow those instructions in addition to

the instructions in this section.

• The server provides one internal SAS/SATA RAID connector and two PCI slots on the system board. See

“System-board internal connectors” on page 26 for the location of the internal SAS/SATA RAID connector
and riser-card slots. You can replace the ServeRAID SAS/SATA adapter with an optional ServeRAID
SAS/SATA adapter in the slot. For configuration information, see the ServeRAID documentation at
http://www.lenovo.com/support.

178

Lenovo System x3550 M5 Installation and Service Guide

«
...
190
191
192
193
194
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Brand: Cabletron Systems Pages: 93

Brand: Watchguard Pages: 32

Brand: Nortel Pages: 144

Brand: t.a.c. Pages: 36

Brand: HPE Pages: 258

Brand: dallmeier Pages: 12

Brand: SEH Pages: 32

Brand: XtendLan Pages: 34

Brand: XtendLan Pages: 51

Brand: Ioimage Pages: 72

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 74

SocketEthernetIP EN60601

Brand: Multitech Pages: 2

Brand: Air Live Pages: 88

Brand: RFL Electronics Pages: 20

Brand: 360 Systems Pages: 137

Supero SuperServer 5016I-T

Brand: Supero Pages: 98

Supero SC808LT-780B

Brand: Supero Pages: 60

SUPER SuperServer 5036I-IF

Brand: Supero Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands