manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

remove or install the component while the server is running. Orange can also indicate touch points on
hot-swap components. See the instructions for removing or installing a specific hot-swap component for
any additional procedures that you might have to perform before you remove or install the component.

System-board internal connectors

The following illustration shows the internal connectors on the system board.

Coin-cell battery

Fan 8
connector

Operator information
panel connector

Fan 7
connector

Fan 6
connector

Fan 5
connector

Fan 3
connector

Fan 2
connector

Fan 1
connector

PCI riser-card
assembly
connector 1

PCI riser-card
assembly
connector 2

Microprocessor 2

Microprocessor 1

Front video
connector

LCD display
panel connector

Front USB
connector

DVD drive connector

ServerRAID
connector

Graphic card
connector

Backplane
configuration
connector

Backplane

connector

DIMM 19-24

DIMM 7-18

DIMM 1- 6

USB hypervisor connector

SAS/SATA cable 
connector 0

power

Figure 25. System-board internal connectors

System-board external connectors

The following illustration shows the external connectors on the system board.

26

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Mako 6500 Setup & Configuration Instructions Manual preview
6500
Brand: Mako Pages: 56
NComputing L130 User Manual preview
L130
Brand: NComputing Pages: 95
LaCie 5big - Network NAS Server Quick Start Manual preview
5big - Network NAS Server
Brand: LaCie Pages: 9
LaCie 2big NAS Quick Install Manual preview
2big NAS
Brand: LaCie Pages: 14
NEC NEAX2000 IVS Series System Manual preview
NEAX2000 IVS Series
Brand: NEC Pages: 160
Microsoft Azure StorSimple 8100 Hardware Installation Manual preview
Azure StorSimple 8100
Brand: Microsoft Pages: 12
IBM AMD Opteron LS20 Type 8850 Installation And User Manual preview
AMD Opteron LS20 Type 8850
Brand: IBM Pages: 68
Xyplex MAXserver 1600 Hardware Installation And Maintenance Manual preview
MAXserver 1600
Brand: Xyplex Pages: 58
H3C UniServer T1100 G3 User Manual preview
UniServer T1100 G3
Brand: H3C Pages: 138
Lantronix xPort Pro XPP1004000-02R Integration Manual preview
xPort Pro XPP1004000-02R
Brand: Lantronix Pages: 17
Gigabyte W131-X30 Quick Installation Manual preview
W131-X30
Brand: Gigabyte Pages: 2
Speco ONSIP OS101 User Manual preview
ONSIP OS101
Brand: Speco Pages: 28
Ericsson HL950 Administrator'S Manual preview
HL950
Brand: Ericsson Pages: 159
Opengear cm4008 Quick Start Manual preview
cm4008
Brand: Opengear Pages: 4
HP 376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch User Manual preview
376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch
Brand: HP Pages: 169
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual preview
PRIMERGY CX400 M6
Brand: Fujitsu Pages: 209
Fujitsu PRIMERGY CX272 S1 Upgrade And Maintenance Manual preview
PRIMERGY CX272 S1
Brand: Fujitsu Pages: 234
Fujitsu Primergy CX270 S2 Upgrade And Maintenance Manual preview
Primergy CX270 S2
Brand: Fujitsu Pages: 320

Brands by name

Popular brands

Load more brands