Lenovo System x3550 M5 Installation And Service Manual Download Page 982

Page: 982 / 1144

2. Verify whether the firmware is at proper level.

3. Rerun the test.

4. If the problem remains, contact your IBM technical-support representative.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

218-906-000 : Brocade:InternalLoopbackTest Failed

A failure was detected during the Loopback test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Rerun the test.

2. Verify whether the firmware is at proper level.

3. Rerun the test.

4. If the problem remains, contact your IBM technical-support representative.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA checkpoint panel test results

The following messages can result when you run the checkpoint panel test.

Test results for the DSA checkpoint panel test

The following messages can result when you run the DSA checkpoint panel test.

•

180-000-000 : Check-point Panel Test Passed

Check-point Panel Test Passed.

968

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands