Lenovo System x3550 M5 Installation And Service Manual Download Page 247

Page: 247 / 1144

Step 6.

Locate the coin-cell battery connector on the system board.

Coin-cell battery

Figure 151. Location of the coin-cell battery connector on system board

Tilt the battery so that you can insert it into the socket on the side opposite the battery clip.

Figure 152. Coin-cell battery installation

Press the battery down into the socket until it clicks into place. Make sure that the battery clip
holds the battery securely.

If you removed a rubber cover from the battery holder, use your fingers to install the battery
cover on top of the battery connector.

Step 7.

Reinstall PCI riser-card assembly 1 (see “Replacing a PCI riser-card assembly” on page 172 or
“Replacing the rear 2.5-inch hot-swap-drive kit” on page 143), if necessary.

Step 8.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 9.

Slide the server into the rack.

Chapter 5

Removing and replacing components

233

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands