Lenovo System x3550 M5 Installation And Service Manual Download Page 150 | Manualshive

Page: 150 / 1144

background image

Removing hot-swap hard disk drives

Use this information to remove hot-swap hard disk drives.

Attention:

• To avoid damage to the hard disk drive connectors, make sure that the server cover is in place and fully

closed whenever you install or remove a hard disk drive.

• To make sure that there is adequate system cooling, do not operate the server for more than 2 minutes

without either a hard disk drive or a filler panel installed in each bay.

• Before you make changes to disk drives, disk drive controllers (including controllers that are integrated

on the system board), disk drive backplanes, or disk drive cables, back up all important data that is
stored on hard disks.

• Before you remove any component of a RAID array, back up all RAID configuration information.

To remove a hot-swap hard disk drive, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Make sure that you save the data on your drive, especially if it is part of a RAID array, before you
remove it from the server.

Step 3.

Slide the release latch (orange) gently to the left to unlock the drive handle.

000000000000000

000000000000000

000000000000000

000000000000000

000000000000000

000000000000000

000000000000000

000000000000000

000000000000000

000000000000000

0000000000

0000000000

0000000000

0000000000

0000000000

0000000000

0000000000

Drive handle

Drive handle

2.5-inch hot-swap
hard disk drive

3.5-inch hot-swap
hard disk drive

Figure 55. Hot-swap hard disk drives removal

Step 4.

Grasp the handle and slide the drive out of the drive bay.

Step 5.

Reinstall the drive bay filler panel.

Step 6.

If you are instructed to return the drive assembly, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Replacing hot-swap hard disk drives

Use this information to replace hot-swap hard disk drives.

The following notes describe the type of hard disk drives that the server supports and other information
that you must consider when you install a hard disk drive. For a list of supported hard disk drives, see
http://www.lenovo.com/ serverproven/.

• Locate the documentation that comes with the hard disk drive and follow those instructions in addition to

the instructions in this chapter.

• Make sure that you have all the cables and other equipment that are specified in the documentation that

comes with the drive.

136

Lenovo System x3550 M5 Installation and Service Guide

«
...
148
149
150
151
152
...
»

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Z10 BUISNESS CLASS Z10 BC

Brand: IBM Pages: 67

x3450 - System - 7948

Brand: IBM Pages: 2

Brand: Atop Pages: 2

Brand: IBM Pages: 140

Brand: Longshine Pages: 56

Brand: Bang & Olufsen Pages: 28

Brand: TP-Link Pages: 16

AMX Vision2 V2-MASTER-1210

Brand: Harman Pages: 2

Brand: Fujitsu Siemens Computers Pages: 68

Brand: Advantech Pages: 43

Sun Fire Netra 1280

Brand: Sun Microsystems Pages: 10

Brand: 3onedata Pages: 3

Brand: disguise Pages: 12

ProLiant ML350 G3

Brand: HP Pages: 44

ProLiant ML310e Gen8 v2

Brand: HP Pages: 43

ProLiant ML330 Generation 3

Brand: HP Pages: 34

PROLIANT ML350 G6

Brand: HP Pages: 145

ProLiant ML350 Gen9

Brand: HP Pages: 171

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands