Lenovo System x3550 M5 Installation And Service Manual Download Page 370

Page: 370 / 1144

User Response

Information only; no action is required.

•

40000082-00000000 : The measured power value has returned below the power cap value.

Power exceeded cap recovered

May also be shown as 4000008200000000 or 0x4000008200000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Power

SNMP Trap ID

164

CIM Information

Prefix:

IMM

ID:

0130

User Response

Information only; no action is required.

•

40000083-00000000 : The new minimum power cap value has returned below the power cap value.

Minimum Power Cap exceeds Power Cap recovered

May also be shown as 4000008300000000 or 0x4000008300000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Power

SNMP Trap ID

164

CIM Information

Prefix:

IMM

ID:

0131

User Response

Information only; no action is required.

356

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands