manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 4.

Align the air baffle pins with the baffle pin holes on both sides of the chassis; then, lower the air
baffle into the server. Press the air baffle down until it is securely seated.

Note:

Close the retaining clip on each end of the DIMM connector before installing the air baffle for

proper cooling.

Baffle pin hole

Baffle pin

Baffle pin

Baffle pin hole

Air baffle

Figure 40. Air baffle installation

Step 5.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 6.

Slide the server into the rack.

Step 7.

Reconnect the power cords and any cables that you removed.

Step 8.

Turn on the peripheral devices and the server.

Removing a RAID adapter battery or flash power module

Use this information to remove a remotely installed RAID adapter battery or flash power module.

To remove a RAID adapter battery or flash power module, complete the following steps:

Note:

The 2.5-inch hard disk drive server model supports up to two RAID adapter batteries or flash

power modules, while the 3.5-inch hard disk drive server model supports only one RAID adapter battery
or flash power module.

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 119).

Chapter 5

.

Removing and replacing components

123

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Lantronix SLC 8000 Demo Manual preview
SLC 8000
Brand: Lantronix Pages: 10
Lantronix xport pro Integration Manual preview
xport pro
Brand: Lantronix Pages: 17
Lantronix PremierWave XC User Manual preview
PremierWave XC
Brand: Lantronix Pages: 109
Lantronix XPort Integration Manual preview
XPort
Brand: Lantronix Pages: 24
Lantronix WiPort Integration Manual preview
WiPort
Brand: Lantronix Pages: 29
Lantronix XPress DR+ Quick Connect preview
XPress DR+
Brand: Lantronix Pages: 2
Premio FlacheSAN1L-D4 Quick Manual preview
FlacheSAN1L-D4
Brand: Premio Pages: 3
Supermicro SUPERSERVER 5019S-M User Manual preview
SUPERSERVER 5019S-M
Brand: Supermicro Pages: 65
Johnson Controls Rackmount 5000 Series Quick Installation Manual preview
Rackmount 5000 Series
Brand: Johnson Controls Pages: 42
QNAP TS 77 Series User Manual preview
TS 77 Series
Brand: QNAP Pages: 69
Tiger Technology Tiger Box 1U8 Assembly Manual preview
Tiger Box 1U8
Brand: Tiger Technology Pages: 29
MAXDATA PLATINUM 500 I Quick Start Manual preview
PLATINUM 500 I
Brand: MAXDATA Pages: 2
MAXDATA SR 1202 Quick Manual preview
SR 1202
Brand: MAXDATA Pages: 6
Grafenthal R2210 S2 User Manual preview
R2210 S2
Brand: Grafenthal Pages: 99
ANTAIRA STE-501C User Manual preview
STE-501C
Brand: ANTAIRA Pages: 51
Black Box LWS401A User Manual preview
LWS401A
Brand: Black Box Pages: 22
Black Box LWS300A User Manual preview
LWS300A
Brand: Black Box Pages: 28
Red Hat DIRECTORY SERVER 7.1 SP7 - S Release Note preview
DIRECTORY SERVER 7.1 SP7 - S
Brand: Red Hat Pages: 12

Brands by name

Popular brands

Load more brands