Lenovo System x3550 M5 Installation And Service Manual Download Page 337

Page: 337 / 1144

A user has modified the telnet port number

May also be shown as 4000003d00000000 or 0x4000003d00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0061

User Response

Information only; no action is required.

•

4000003e-00000000 : SSH port number changed from [arg1] to [arg2] by user [arg3].

A user has modified the SSH port number

May also be shown as 4000003e00000000 or 0x4000003e00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0062

User Response

Information only; no action is required.

•

4000003f-00000000 : Web-HTTP port number changed from [arg1] to [arg2] by user [arg3].

A user has modified the Web HTTP port number

May also be shown as 4000003f00000000 or 0x4000003f00000000

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

323

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands