manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

SNMP Trap ID

41

CIM Information

Prefix:

PLAT

ID:

0802

User Response

1. Check the system-event log for DIMM failure events (uncorrectable or PFA) and correct the

failures.

2. Re-enable mirroring in the Setup utility.

•

800b0309-1301ffff : Non-redundant:Sufficient Resources from Redundancy Degraded or Fully

Redundant for [RedundancySetElementName] has asserted. (Power Resource)

This message is for the use case when a Redundancy Set has transitioned from Redundancy Degraded
or Fully Redundant to Non-redundant:Sufficient.

May also be shown as 800b03091301ffff or 0x800b03091301ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

No

Alert Category

Warning - Redundant Power Supply

SNMP Trap ID

10

CIM Information

Prefix:

PLAT

ID:

0806

User Response

1. Non-redundant sufficient: Power load will be handled by remaining power supply, though the

system may throttle to avoid a power supply over-current condition.

2. Replace the power supply with higher rated power.

•

800b030c-2581ffff : Non-redundant:Sufficient Resources from Redundancy Degraded or Fully

Redundant for [RedundancySetElementName] has asserted. (Backup Memory)

This message is for the use case when a Redundancy Set has transitioned from Redundancy Degraded
or Fully Redundant to Non-redundant:Sufficient.

May also be shown as 800b030c2581ffff or 0x800b030c2581ffff

Severity

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

465

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

NEC Express5800/T110g-E Quick Start Manual preview
Express5800/T110g-E
Brand: NEC Pages: 2
Supermicro SUPERSERVER 6034H-X8R User Manual preview
SUPERSERVER 6034H-X8R
Brand: Supermicro Pages: 128
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
BELINEA o.center User Manual preview
o.center
Brand: BELINEA Pages: 53
Supero SUPERO SuperServer 6026TT-H6IBQRF User Manual preview
SUPERO SuperServer 6026TT-H6IBQRF
Brand: Supero Pages: 110
Sun Microsystems Sun Ray 150 User Manual preview
Sun Ray 150
Brand: Sun Microsystems Pages: 121
Dell PowerEdge M630 Owner'S Manual preview
PowerEdge M630
Brand: Dell Pages: 129
Dell PowerEdge HR675 Hardware Owner'S Manual preview
PowerEdge HR675
Brand: Dell Pages: 194
Dell PowerEdge FC630 Owner'S Manual preview
PowerEdge FC630
Brand: Dell Pages: 143
Dell PowerEdge HX574 Hardware Owner'S Manual preview
PowerEdge HX574
Brand: Dell Pages: 202
Dell Wyse 5020 P Series Quick Start Manual preview
Wyse 5020 P Series
Brand: Dell Pages: 8
Dell Wyse 3020 Quick Start Up Manual preview
Wyse 3020
Brand: Dell Pages: 2
Dell Wyse 5030 User Manual preview
Wyse 5030
Brand: Dell Pages: 12
Dell Wyse 5000 Series Quick Start Manual preview
Wyse 5000 Series
Brand: Dell Pages: 8
Dell Wyse7020 Quick Start Manual preview
Wyse7020
Brand: Dell Pages: 2
Dell Wyse 3030 Quick Start Manual preview
Wyse 3030
Brand: Dell Pages: 2
Dell Wyse 5020 Quick Start Manual preview
Wyse 5020
Brand: Dell Pages: 8
Dell XC6320 Owner'S Manual preview
XC6320
Brand: Dell Pages: 91

Brands by name

Popular brands

Load more brands