manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 5.

Locate the microprocessor to be removed (see “System-board internal connectors” on page 26).

Step 6.

Remove the heat sink.

Attention:

Do not touch the thermal material on the bottom of the heat sink. Touching the thermal

material will contaminate it. If the thermal material on the microprocessor or heat sink becomes
contaminated, you must wipe off the contaminated thermal material on the microprocessor or heat
sink with the alcohol wipes and reapply clean thermal grease to the heat sink.

a.

Use a screwdriver to loosen the captive screw on one side of the heat sink to break the seal
with the microprocessor.

b.

Loosen all the captive screws on the heat sink, rotating each screw one full turn until each
screw is loose.

c.

Gently lift the heat sink from the microprocessor. After removal, place the heat sink (with the
thermal grease side up) on a clean, flat surface.

Heat sink

Figure 192. Heat sink removal

Step 7.

Open the microprocessor socket release levers and retainer.

Microprocessor 
release lever

Microprocessor 
release lever

Figure 193. Microprocessor socket levers and retainer disengagement

a.

Identify which release lever is labeled as the first release lever to open and open it.

264

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Brand: G-Technology Pages: 35
H3C UniServer R6900 G5 Manual preview
UniServer R6900 G5
Brand: H3C Pages: 83
IBM 88631SU - System x3850 - 8863 Installation Manual preview
88631SU - System x3850 - 8863
Brand: IBM Pages: 90
HPE ProLiant DL180 Gen10 Product End-Of-Life Disassembly Instructions preview
ProLiant DL180 Gen10
Brand: HPE Pages: 10
Lanner LEC-3010 User Manual preview
LEC-3010
Brand: Lanner Pages: 43
IBM Flex System x240 Compute Node Product Manual preview
Flex System x240 Compute Node
Brand: IBM Pages: 28
Oki ML590 Specification Sheet preview
ML590
Brand: Oki Pages: 2
Blackberry Enterprise Server Upgrade Manual preview
Enterprise Server
Brand: Blackberry Pages: 88
X-media XM-PS110P Quick Installation Manual preview
XM-PS110P
Brand: X-media Pages: 10
HPE ProLiant ML110 Gen 10 Product End-Of-Life Disassembly Instructions preview
ProLiant ML110 Gen 10
Brand: HPE Pages: 5
Belkin F1UP0002 Quick Installation Manual preview
F1UP0002
Brand: Belkin Pages: 2
Netstor NA762TB3 User Manual preview
NA762TB3
Brand: Netstor Pages: 17
disguise rx Hardware Manual preview
rx
Brand: disguise Pages: 12
7th Sense DeltaServer User Manual preview
DeltaServer
Brand: 7th Sense Pages: 60
SAFARI Montage T-440i Installation Manual preview
T-440i
Brand: SAFARI Montage Pages: 8
SAFARI Montage WAN–1212 Installation Manual preview
WAN–1212
Brand: SAFARI Montage Pages: 8
Planet NAS-7102 User Manual preview
NAS-7102
Brand: Planet Pages: 68
ClearCube A6108 Quick Start Manual preview
A6108
Brand: ClearCube Pages: 15

Brands by name

Popular brands

Load more brands