Lenovo System x3550 M5 Installation And Service Manual Download Page 186

Page: 186 / 1144

Replacing a PCI riser-card assembly

Use this information to replace a PCI riser-card assembly.

Note:

PCI riser-card brackets must be installed even if you do not install an adapter.

The following table lists the supported PCI riser-card assembly configurations in the server.

Table 32. Configuration 1

Configuration 1

PCI riser-card assembly

connector 1 on system board

PCI riser-card assembly

connector 2 on system board

Configuration

Number of

microprocessors

installed

Slot 1

Slot 2

Slot 3

• Three

low-profile
slots

One

x1/x4/x8/x16 low-profile

x1/x4/x8

low-profile

x1/x4/x8

low-profile

Table 33. Configuration 2

Configuration 2

PCI riser-card assembly

connector 1 on system board

PCI riser-card assembly

connector 2 on system board

Configuration

Number of

microprocessors

installed

Slot 1

Slot 2

Slot 3

• Three

low-profile
slots

Two

x1/x4/x8/x16 low-profile

x1/x4/x8/x16

low-profile

x1/x4/x8/x16

low-profile

Table 34. Configuration 3

Note:

Slot 1 is for the 60-mm ML2 adapter.

Configuration 3

PCI riser-card assembly

connector 1 on system board

PCI riser-card assembly

connector 2 on system board

Configuration

Number of

microprocessors

installed

Slot 1

Slot 2

Slot 3

• One ML2 slot

• One

full-height,
half-length slot

• One

low-profile slot

One

ML2

x1/x4/x8

full-height,
half-length

x1/x4/x8

low-profile

172

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands