Lenovo System x3550 M5 Installation And Service Manual Download Page 717

Page: 717 / 1144

May also be shown as 810100020701ffff or 0x810100020701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0477

User Response

No action; information only.

•

81010202-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102020701ffff or 0x810102020701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. SysBrd 12V : SysBrd 3.3V : SysBrd 5V :

•

81010204-1d01ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 1A Tach)

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

703

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands