manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

3. If error persists, or boot is unsuccessful, (Trained service technician only) Replace the system

board.

•

I.3818002 The firmware image capsule signature for the non-booted flash bank is invalid. Opposite

Bank CRTM Capsule Update Signature Invalid

Explanation:

Severity

Info

User Response

Complete the following steps:

1. Update the backup UEFI image.

2. If error does not persist no additional recovery action is required.

3. If error persists, or boot is unsuccessful, (Trained service technician only) Replace the system

board.

•

I.3818003 The CRTM flash driver could not lock the secure flash region. CRTM Could not lock

secure flash region

Explanation:

Severity

Info

User Response

Complete the following steps:

1. If system failed to boot successfully, DC cycle the system.

2. If system boots to F1 setup, update the UEFI image and reset bank to primary (if required). If the

system boots without error, recovery is complete and no additional action is required.

3. If system fails to boot, or if the firmware update attempt fails, (trained service technician only)

replace the system board.

•

I.3818009 The TPM could not be properly initialized. TPMINIT: Fail to initialize TPM chip.

Explanation:

Severity

Info

User Response

Complete the following steps:

1. Check the Lenovo support site for an applicable service bulletin or firmware update that

applies to this error.

2.

Reboot the system.

3. If the error continues, replace the system-board assembly (see Removing the system-board

assembly and Installing the system-board assembly).

930

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

IBM QS21 - BladeCenter - 0792 Installation And User Manual preview
QS21 - BladeCenter - 0792
Brand: IBM Pages: 110
Jatheon PnC 100 Installation & Administrators Manual preview
PnC 100
Brand: Jatheon Pages: 52
IBM 88643RU - System x3850 - 8864 Service Manual preview
88643RU - System x3850 - 8864
Brand: IBM Pages: 192
I-O DATA FIDATA HFAS1-S10U Setup Manual preview
FIDATA HFAS1-S10U
Brand: I-O DATA Pages: 46
Ekselans 280053 User Manual preview
280053
Brand: Ekselans Pages: 37
Supero SUPERSERVER 7045W-NTR+ User Manual preview
SUPERSERVER 7045W-NTR+
Brand: Supero Pages: 146
Thecus N299 User Manual preview
N299
Brand: Thecus Pages: 94
HP ProLiant Moonshot Specification preview
ProLiant Moonshot
Brand: HP Pages: 21
F5 BIG-IP 8950 Platform Manual preview
BIG-IP 8950
Brand: F5 Pages: 56
EVS XT2+ Technical Reference Hardware Manual preview
XT2+
Brand: EVS Pages: 87
Viavi G3-GS-8P-576T Hardware Installation preview
G3-GS-8P-576T
Brand: Viavi Pages: 8
Viavi G4-10G-010-96T Manual preview
G4-10G-010-96T
Brand: Viavi Pages: 12
Adaptec 5325302053 - Snap Server 720i NAS User Manual preview
5325302053 - Snap Server 720i NAS
Brand: Adaptec Pages: 238
VC Videocomponents 11902 Mounting And Operating Manual preview
11902
Brand: VC Videocomponents Pages: 84
VBrick Systems EtherneTV v4.2.1 Portal Server Admin Manual preview
EtherneTV v4.2.1 Portal Server
Brand: VBrick Systems Pages: 180
Wiredocean SBS 1000 Owners Handbook And Installation Instructions preview
SBS 1000
Brand: Wiredocean Pages: 36
10ZiG Technology Limited RBT-402 Quick Start Manual preview
RBT-402
Brand: 10ZiG Technology Limited Pages: 2
Seagate NAS Pro 2-Bay Manual preview
NAS Pro 2-Bay
Brand: Seagate Pages: 69

Brands by name

Popular brands

Load more brands