Lenovo System x3550 M5 Installation And Service Manual Download Page 967

Page: 967 / 1144

•

405-802-000 : BRCM:TestEEPROM Test Aborted

The EEPROM test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

405-803-000 : BRCM:TestInternalMemory Test Aborted

The internal memory test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

405-804-000 : BRCM:TestInterrupt Test Aborted

The interrupt test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Appendix C. DSA diagnostic test results

953

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands