Lenovo System x3550 M5 Installation And Service Manual Download Page 142

Page: 142 / 1144

Step 6.

Route the cable along the chassis.

Note:

The cable routing is different between 2.5-inch and 3.5-inch hard disk drive server models.

Figure 45. RAID adapter battery or flash power module cable connection for 3.5-inch hard disk drive server
models

128

Lenovo System x3550 M5 Installation and Service Guide

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands