Lenovo System x3550 M5 Installation And Service Manual Download Page 813

Page: 813 / 1144

This message is for the use case when an implementation has detected a Managed Element is now
Present.

May also be shown as 816f01251001ffff or 0x816f01251001ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0390

User Response

No action; information only.

•

816f0125-1002ffff : [ManagedElementName] detected as present. (PCI Riser 2)

This message is for the use case when an implementation has detected a Managed Element is now
Present.

May also be shown as 816f01251002ffff or 0x816f01251002ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0390

User Response

No action; information only.

•

816f0125-2c01ffff : [ManagedElementName] detected as present. (ML2 Card)

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

799

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands