manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

SAS/SATA power cable

SAS/SATA signal
cable

SAS/SATA power
connector

Figure 146. Four 3.5-inch simple-swap backplate assembly cable connection

Step 4.

Reinstall the hard disk drives and filler panels (see “Replacing simple-swap hard disk drives” on
page 138).

Step 5.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 6.

Slide the server into the rack.

Step 7.

Reconnect the power cords and any cables that you removed.

Step 8.

Turn on the peripheral devices and the server.

Removing a USB embedded hypervisor flash device

Use this information to remove a USB embedded hypervisor flash device.

To remove a USB hypervisor flash device, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 119).

Chapter 5

.

Removing and replacing components

227

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

D-Link DP 301U Quick Installaion Manual preview
DP 301U
Brand: D-Link Pages: 12
IBM 610 Technical Overview And Introduction preview
610
Brand: IBM Pages: 40
IBM 88631SU - System x3850 - 8863 Installation Manual preview
88631SU - System x3850 - 8863
Brand: IBM Pages: 90
Aaeon AIOT-ILRA01 User Manual preview
AIOT-ILRA01
Brand: Aaeon Pages: 38
H3C UniServer BT716F User Manual preview
UniServer BT716F
Brand: H3C Pages: 44
Patton electronics PeNet 2127 User Manual preview
PeNet 2127
Brand: Patton electronics Pages: 16
AIC SB401-MN User Manual preview
SB401-MN
Brand: AIC Pages: 88
GlobalTime Electronic GTT-400 Manual preview
GTT-400
Brand: GlobalTime Electronic Pages: 19
BlueNet Video BB01D User Manual preview
BB01D
Brand: BlueNet Video Pages: 38
Olive Olive OPUS N5 User Manual preview
Olive OPUS N5
Brand: Olive Pages: 24
D-Link DP-100 Hardware User'S Manual preview
DP-100
Brand: D-Link Pages: 32
D-Link DP-101 Hardware Manual preview
DP-101
Brand: D-Link Pages: 22
D-Link DP-313 - Air 802.11b Wireless Print Server User Manual preview
DP-313 - Air 802.11b Wireless Print Server
Brand: D-Link Pages: 28
D-Link DP 301U Quick Installation Manual preview
DP 301U
Brand: D-Link Pages: 64
D-Link D DP-301P+ DP-301P+ Datasheet preview
D DP-301P+ DP-301P+
Brand: D-Link Pages: 2
D-Link DP-802 User Manual preview
DP-802
Brand: D-Link Pages: 100
D-Link AirPlus G DP-G301 Manual preview
AirPlus G DP-G301
Brand: D-Link Pages: 88
D-Link DP-100+ User Manual preview
DP-100+
Brand: D-Link Pages: 37

Brands by name

Popular brands

Load more brands