background image

1

3

Installing internal options

If internal options have been purchased separately, install them before installing an operating system.

If you use Custom Made Service, installing internal options is not required. Just check "

n

 Points to note before 

installing an OS".

1

Checking the items 

supplied

Check the contents in the package using 

the "Contents List".

If any items are missing, contact an office listed in the 

"Contact Information".

2

Reading and understanding 

"Safety Precautions"

Before using this server, be sure to read and under-

stand the attached "Safety Precautions".

Points to note before installing internal 

    options

Make sure to read the following manuals for operations. 

 "Chapter 6 Installing Internal Options"

 "PRIMERGY Server Books"/"Supplement"

Points to note before installing an OS

When using the optional devices listed below, note the fol-

lowing instruction before installing an OS.

- USB optional devices other than FDD

Install USB optional devices other than a floppy disk drive

after installing an OS.

- Internal Data Cartridge Drive Unit

Insert a data cartridge after installing an OS.

If a data cartridge is inserted, remove it.

- Optional external devices

-  When hard disk units are installed in PRIMERGY SX35 

with arrays configured, delete the array configuration. 

After installing an OS, configure the arrays again.

-  When connecting an external storage system such as 

ETERNUS, do not turn on the power until the OS instal-

lation completes.

Available internal options and installation 

    locations

  

After installing internal options, check that the order 

and location of installation are correct and cables 

are correctly connected.

RX600 S4

B7FH-5691-01EN-00

���

��������������

������������������
������������������������

��������������������
��������������������������

���������������

�������������

n

PRIMERGY RX600 S4 Manuals

Manuals for this server are stored in PRIMERGY Startup Disc. Insert the PRIMERGY Startup Disc and click [PRIMERGY Manuals] on the 

[PRIMERGY Startup Disc] screen to refer to the manuals.

The manuals can be read using Acrobat

®

 Reader

®

 or Adobe

®

 Reader

®

. When using Acrobat

®

 Reader

®

, use version 5.0 or later.

Summary of Contents for Primergy RX600









Reviews: