Keysight N9923A User Manual Download Page 191

Page: 191 / 276

191

Keysight N9923A Handheld Analyzer
User’s Guide

13 File Management

The FieldFox can save any of the following types of files:

— Current settings and calibration

— Trace data (*.csv, *.S1P, *.S2P)

— Picture of the FieldFox screen
In addition, files can be saved to the internal memory, a USB Flash drive, or a
standard SD card.

In this Chapter

“Save Files” on page 192

“Recall Files” on page 195

“Move (Copy) Files” on page 195

“Set File Type and Select Device” on page 196

“Manage Files” on page 199

“Manage Folders” on page 200

“Edit Keywords” on page 201

“Prefixes and Suffixes for Filenames” on page 202

See Also:

“Erase User Data” on page 235

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 191 / 276

Search results

Summary of Contents for N9923A

Reviews: