Keysight N9923A User Manual Download Page 143

Page: 143 / 276

Keysight N9923-90001 User’s Guide 143

Frequency Offset Using Power Sensor (FOPS) – Option 208
FOPS Settings

—

Dwell /Point

Specifies a settling time (in seconds) after the internal source

steps to the next frequency and before the power sensor makes a

measurement.

Amplitude Markers

Amplitude markers are horizontal dotted lines that you can move to any
amplitude level on the screen. The two amplitude markers can be set

independently or used as a pair of delta markers. Amplitude markers can be
used as a visual comparison aid with the data trace.

How to make Amplitude Marker settings

— Press

Marker

— Then

More

— Then

Ampl Markers

— Then choose from the following:

—

OFF

Amplitude markers are NOT displayed.

—

Amplitude markers ARE displayed at their previous positions.

— Then

Ampl Mkr 1 or 2

— Enter a value in dBm for the marker using the numeric keypad, the

arrows, or the rotary knob.

— Press

Delta Ampl Mkr

— Then choose from the following:

—

AmplMkr 2 value is relative to AmplMkr 1. When AmplMkr 1 is

moved, AmplMkr 2 also moves to maintain the AmplMkr 2 value
between them.

—

OFF

The two amplitude markers move independent of one another.

Trace Math

Trace Math allows you to compare data traces and perform simple math. Learn

how to use Trace Math in

“All about Trace Math” on page 189

. All Data and

Memory features work as documented EXCEPT for the following:

To Compare Src Power (Input) and Rx Power (Output):

Meas Rx Power

Store to memory

View Data & Memory

Meas Src Power.

When Trace, then Data -> Mem is pressed, if a Src Power trace is active,

then RxPower is actually stored into memory.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 143 / 276

Search results

Summary of Contents for N9923A

Reviews: