Keysight N9923A User Manual Download Page 169

Page: 169 / 276

Keysight N9923-90001 User’s Guide 169

VVM (Vector Voltmeter) Mode - Option 308
1-Port Cable Trimming Measurements

1-Port Cable Trimming Measurements

A 1-Port Cable Trimming measurement is used in a cable fabrication procedure

to validate proper electrical length.

How to make a 1-Port Cable Trimming Measurement

Press

Mode

then

VVM

then

1-Port Cable Trimming

Press

Freq/Dist

then enter the frequency for the measurement.

Press

Meas Setup 4

then

Zero OFF

Optionally calibrate the FieldFox. Learn more about VVM calibration in

“VVM Calibration” on page 167

—

If using an adapter to connect the cables to the FieldFox, press Cal

5 then select either QuickCal or Mechanical Cal. Follow the FieldFox

calibration prompts. During calibration, the measurement

(S-parameter) is referred to as S11.

—

If connecting the cables directly to the FieldFox test port, CalReady

is very accurate.

To ensure that the calibration is adequate, perform the following

optional

Measurement Verification

procedure.

Connect a short standard to

PORT 1

where cables to be trimmed

will be connected.

Press

Meas Setup 4

and press

Zero

Remove the short standard and connect the open standard.

Confirm that magnitude measurement is less than –0.1 dB and that

the phase value reads 180° degrees.

— The R receiver measures incident

signal (green line) out of the source.

— The A receiver measures reflected

signal (red line) from the end of the
DUT (black line).

— In VVM mode, the display ALWAYS

shows ratioed (A/R) measurements
which is the electrical length of the
DUT.

This measurement verification procedure is suitable for low frequency

measurements. However, for high frequency measurements, a more

sophisticated procedure is required.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 169 / 276

Search results

Summary of Contents for N9923A

Reviews: