Keysight N9923A User Manual Download Page 233

Page: 233 / 276

Keysight N9923-90001 User’s Guide

233

System Settings
FieldFox Package Installer (Applies to N9912A units with serial number prefixes ≥5607)

FieldFox Package Installer (Applies to N9912A units with serial
number prefixes ≥5607)

The FieldFox Package Installer enables you to download new versions of

firmware from either a USB memory or SD Card. Additionally, the Utility softkey
enables you to backup user files or restore user files.

How to run the Installer

— Press

System 7

— Then

System Configuration

— Then

More

— Then

Firmware Update

— Then

Start Installer

— The Installer software opens after a couple of seconds.

— Then the

arrows or the knob to scroll to the firmware you want to

install.

— Press

Start Install

— “

Current Step Progress:

” bar and a “

Total Progress:

” bar are

displayed along with this message: “

Copying package. Do not

remove install media.

”

— When the installation is completed, the FieldFox reboots.

How to backup files

This procedure backs up your user data to a USB or SD card. See also

“How to

restore files” on page 234

From the initial Installer menu:

— Press

Utility

Before running the Installer to update your firmware, you might want to

back up your user data. Refer to

“How to restore files” on page 234

If no files are displayed, verify that a USB memory or SD Card is installed
and press

Refresh List

If you backup multiple versions of the user files, the FieldFox appends a

“_#” to each subsequently stored file. During restore, the file with the
highest appended number is loaded into the FieldFox.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 233 / 276

Search results

Summary of Contents for N9923A

Reviews: