Keysight N9923A User Manual Download Page 232

Page: 232 / 276

232 Keysight N9923-90001 User’s Guide

System Settings
Power ON

—

DHCP

- IP Address is assigned dynamically. If your server supports this

feature, the IP Address for the FieldFox is assigned each time it is

started.

—

Static

- Set the IP Address manually. The Address remains until you

change it.

—

Static IP Address

- Enter the IP Address – including periods - in the format

nnn.nnn.nnn.nnn

—

Static Subnet Mask

- Enter the Subnet Mask – including periods - in the

format nnn.nnn.nnn.nnn

—

Static Gateway

- Enter the Static Gateway – including periods - in the

format nnn.nnn.nnn.nnn

—

Apply Settings

Choose from:

—

Power Up

The above settings take effect when the FieldFox is started.

—

Now

The above settings take effect immediately.

— Press

Done Edit

when finished.

Power ON

When the FieldFox is without a power source, this setting allows the FieldFox
to power ON as soon as a charged battery or the DC Adapter is inserted

without pressing the power button.

How to set Power ON

— Press

System 7

— Then

System Configuration

— Then

Power ON

— Then choose from the following:

—

Auto

The FieldFox will power ON when a charged battery or the DC

Adapter is inserted.

—

Manual

The FieldFox will power ON only when the power button is

pressed.

To make the LAN settings persist after power up, toggle Apply Settings to

Now then back to Power Up. You should see a message indicating that the

LAN config file was saved.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 232 / 276

Search results

Summary of Contents for N9923A

Reviews: